重庆秒秒彩走势

Hello! Welcome to Dongguan Zhongke Electric Co., Ltd.
Consultation Hotline: 18002896378
Nesw
News Recommendation
Contact us

Dongguan Zhongke Electric Co., Ltd.
QQ:952508676
Contacts Mobile phone: Chen Zhong 18002896378 
Mail Box:cngzk@qq.com
Address:Hetang No。 3, Tongsha Taichufang, Dongcheng City, Dongguan City

Your location: 主页 > News > Common problem >

How to choose a three-phase voltage regulator?

 
  How to choose a three-phase voltage regulator?
 
 
 
First: How to choose a regulator?
 
First of all, it depends on what type of electrical equipment you use. Normally, the load is not purely resistive. Therefore, in the actual selection, the regulated power supply should be reasonably selected according to the rated power, power factor and load type of the electrical equipment. Its output power should be left with appropriate margin, especially when the impulse load is selected, the margin should be larger. How to select the type is as follows:
 
_For pure resistive load such as incandescent lamp, resistor wire, electric furnace and other equipment, the power of regulator should be 1.5 times to 2 times of the power of load equipment.
 
Inductive and capacitive loads such as fluorescent lamps, fans, motors, pumps, air conditioners, computers, refrigerators, etc. The power of the regulator should be three times that of the load equipment.
 
_In the environment of large inductance and capacitance load, the starting current of load should be considered especially large (5-8 times of rated current), so the power of voltage regulator should be more than 3 times of the load power.
 
II: Safety of Regulator
 
_When the power supply is turned on and started, do not disconnect the input and output connections of the power supply or the power supply at will, in order to prevent electric shock or other electrical safety accidents.
 
_The input and output wiring of the regulated power supply must be reasonably arranged to prevent trampling and wearing out, resulting in leakage accidents.
 
_Voltage stabilized power supply must be reliably grounded. The user is responsible for the electric shock or human injury caused by the operation of ungrounded wire.
 
_The ground of voltage stabilized power supply can not be connected to public welfare facilities such as heating pipeline, water supply pipeline and gas pipeline, so as to avoid infringing on the rights of third parties or causing harm.
 
(5) The input and output connections of the regulated power supply should be checked regularly to avoid loosening or falling off, thus affecting the normal use and safety of the three-phase regulated power supply.
 
_The selection of the connection line of the voltage regulator must reach the connection line which can bear enough current capacity.
 
_Regulator should be handled lightly to avoid severe vibration while working.
 
(5) Ensure that the carbon brush spring of the regulator has enough pressure to avoid the fire on the contact surface of the carbon brush and the coil;
 
(6) Non-professionals should not disconnect the regulated power supply or repair it.
三相稳压器
  Installation and Use of Regulator
 
_Connect the regulator to the distribution board and install a fuse on the user's distribution board to ensure the safety of electricity consumption.
 
_Connect the power supply of the electrical equipment to the output terminal of the instrument. Pay attention to the rated input voltage value of the electrical appliances. The output of the three-phase transformer should be the same as that of the regulator.
 
Firstly, turn on the power switch of the regulator, and the working indicator light is on. Observe whether the voltmeter indication is normal. When the output voltage is normal, the voltage regulator can automatically adjust the voltage by switching on the power supply switch of the electrical equipment. The normal power supply regulator manufacturer.
 
When the electrical equipment is not used for a long time, please turn off the power switch of the electrical equipment to reduce power consumption and prolong the service life of the regulator.
 
_Regulator should not be overloaded. When the market voltage is low, the output capacity will be reduced, so the load of the regulator should be reduced accordingly.
 
_When electing electrical appliances with refrigerators, air conditioners, water pumps and other motor-operated equipment, the voltage stabilizer of more than three times the capacity should be selected so as to avoid starting current exceeding the fuse current of the voltage regulator or or overcurrent protection circuit breaker current making the fuse of the voltage regulator fuse fuse or circuit breaker trip or voltage drop too large to work.
 
The conductor connected with the voltage regulator should have enough load surface to prevent heating and reduce pressure drop. Voltage regulators with capacity over 2KVA are connected by terminals. Single copper conductor should be selected, and the terminal screw should be tightened as far as possible to prevent heating at the connection.
 
_Whether single-phase or three-phase regulators, after connecting all input and output lines, the power switch of the load should be turned off first, then the regulator should be turned on, after checking the normal output voltage, then the power switch of the load should be turned on.
关注二维码

© Copyright © 2012-2019 Dongguan Zhongke Electric Co., Ltd. 
Consultation Hotline : 18002896378 Mr.Chen
Firm words:0769-22317946                        
Q   Q:952508676                                 Mail Box:cngzk@qq.com
Address:Hetang No. 3, Tongsha Taichufang, Dongcheng City, Dongguan City

东京1.5分彩登陆 内蒙古快3计划 广东快乐十分 秒速时时彩 香港开奖结果2019+开奖结果 北京快三预测 天津11选5走势图 极速快乐十分 诚信网投开户 秒速三分彩